forked from tasoller/host-aprom
77 lines
2.6 KiB
Markdown
77 lines
2.6 KiB
Markdown
# TASOLLER Custom Firmware (Host MCU - Application ROM)
|
|
|
|
See [Development](./Development.md) for development information.
|
|
|
|
Like what you see? [Buy me a coffee](https://ko-fi.com/bottersnike)
|
|
|
|
## Features
|
|
- Superior slider processing; no more dropped holds or missed notes!
|
|
- Native arcade IO support
|
|
- Air sensor anti-jitter (fixes dodgy sensors)
|
|
- Intuitive menus
|
|
- Arcade-accurate colours
|
|
|
|
And of course, it's all open source :).
|
|
|
|
## Setup
|
|
### Installing Firmware
|
|
- Download both `host_aprom.bin` and `led_aprom.bin`
|
|
- Run `TASOLLER-FirmwareUpdater.exe`
|
|
- Follow the instructions
|
|
|
|
### Configuring segatools
|
|
This firmware emulates arcade IO. As such, segatools' emulation should be disabled, by adding the following lines:
|
|
|
|
```ini
|
|
[slider]
|
|
enable=0
|
|
[io4]
|
|
enable=0
|
|
```
|
|
|
|
Ensure no other `[slider]` section exists in the file (or if it does, set `enable=0` there instead).
|
|
|
|
The slider **MUST** be assigned to port `COM1`. To do this:
|
|
|
|
- Go to `Devices and Printers` in control panel
|
|
- Double click `TASOLLER`
|
|
- In the `Hardware` tab, double click `USB Serial Device`
|
|
- If this already reads `USB Serial Device (COM1)` nothing needs done
|
|
- Click `Change settings`
|
|
- Go to `Port Settings` -> `Advanced...`
|
|
- Under the dropdown for `COM Port Number:` select `COM1`
|
|
|
|
If `COM1` is already in use, check what device it is assigned to in Device Manager under `Ports (COM & LPT)`. You may need to enable `View` -> `Show hidden devices`.
|
|
|
|
Pre-chusan Chunithm uses IO3. This firmware does not (and unfortunately cannot) support IO3. It is recommended to enable the HID keyboard mode, and continue to use keyboard input for IRs.
|
|
|
|
## Controls
|
|
### General
|
|
Tap FN1 to insert a coin. FN2 is currently unbound.
|
|
|
|
### Configuration
|
|
While holding FN1, the following configuration options are available:
|
|
|
|
|
|
|
|
※ "Insert card" will hold the Enter key for 5 seconds
|
|
|
|
### Test menu
|
|
|
|
To enter the system test menu, double-tap FN2. This will mirror the on-screen controls, and additionally adds controls for the TEST and SERVICE buttons on a real cabinet. Double-tap FN2 again to leave this mode on the controller (note that this is not synced with the game exiting the menu!).
|
|
|
|
|
|
|
|
To access the TEST and SERVICE buttons without entering the test menu, hold FN2 instead.
|
|
|
|
|
|
|
|
## Keyboard Mapping
|
|
When the HID keyboard is enabled, the following mapping (UMIGURI defaults) is used:
|
|
|
|
|
|
|
|
with the airs mapped as `0OLP,.`.
|
|
|
|
Please note that this is slightly different to stock firmware!
|