forked from akanyan/STARTLINER
82 lines
2.8 KiB
INI
82 lines
2.8 KiB
INI
[vfd]
|
|
; Enable VFD emulation. Disable to use a real VFD
|
|
; GP1232A02A FUTABA assembly.
|
|
enable=1
|
|
|
|
[system]
|
|
; Enable ALLS system settings.
|
|
enable=1
|
|
|
|
; Enable freeplay mode. This will disable the coin slot and set the game to
|
|
; freeplay. Keep in mind that some game modes (e.g. Freedom/Time Modes) will not
|
|
; allow you to start a game in freeplay mode.
|
|
freeplay=0
|
|
|
|
; LAN Install: If multiple machines are present on the same LAN then set
|
|
; this to 1 on exactly one machine and set this to 0 on all others.
|
|
dipsw1=1
|
|
|
|
; -----------------------------------------------------------------------------
|
|
; Misc. hooks settings
|
|
; -----------------------------------------------------------------------------
|
|
|
|
; -----------------------------------------------------------------------------
|
|
; LED settings
|
|
; -----------------------------------------------------------------------------
|
|
|
|
[led15093]
|
|
; Enable emulation of the 15093-06 controlled lights, which handle the air tower
|
|
; RGBs and the rear LED panel (billboard) on the cabinet.
|
|
enable=1
|
|
|
|
[led]
|
|
; Output billboard LED strip data to a named pipe called "\\.\pipe\chuni_led"
|
|
cabLedOutputPipe=1
|
|
; Output billboard LED strip data to serial
|
|
cabLedOutputSerial=0
|
|
|
|
; Output slider LED data to the named pipe
|
|
controllerLedOutputPipe=1
|
|
; Output slider LED data to the serial port
|
|
controllerLedOutputSerial=0
|
|
; Use the OpeNITHM protocol for serial LED output
|
|
controllerLedOutputOpeNITHM=0
|
|
|
|
; Serial port to send data to if using serial output. Default is COM5.
|
|
;serialPort=COM5
|
|
; Baud rate for serial data (set to 115200 if using OpeNITHM)
|
|
;serialBaud=921600
|
|
|
|
; Data output a sequence of bytes, with JVS-like framing.
|
|
; Each "packet" starts with 0xE0 as a sync. To avoid E0 appearing elsewhere,
|
|
; 0xD0 is used as an escape character -- if you receive D0 in the output, ignore
|
|
; it and use the next sent byte plus one instead.
|
|
;
|
|
; After the sync is one byte for the board number that was updated, followed by
|
|
; the red, green and blue values for each LED.
|
|
;
|
|
; Board 0 has 53 LEDs:
|
|
; [0]-[49]: snakes through left half of billboard (first column starts at top)
|
|
; [50]-[52]: left side partition LEDs
|
|
;
|
|
; Board 1 has 63 LEDs:
|
|
; [0]-[59]: right half of billboard (first column starts at bottom)
|
|
; [60]-[62]: right side partition LEDs
|
|
;
|
|
; Board 2 is the slider and has 31 LEDs:
|
|
; [0]-[31]: slider LEDs right to left BRG, alternating between keys and dividers
|
|
|
|
|
|
; -----------------------------------------------------------------------------
|
|
; Custom IO settings
|
|
; -----------------------------------------------------------------------------
|
|
|
|
[chuniio]
|
|
; Uncomment this if you have custom chuniio implementation comprised of a single 32bit DLL.
|
|
; (will use chu2to3 engine internally)
|
|
;path=
|
|
|
|
; Uncomment both of these if you have custom chuniio implementation comprised of two DLLs.
|
|
; x86 chuniio to path32, x64 to path64. Both are necessary.
|
|
;path32=
|
|
;path64= |